Slump Test
Important Point
- The slump test is used to measure the workability of freshly made concrete. If concrete is made on the plant, a slump test is done on the plant itself.
- Equipment for slump tests can be easily carried on site. No specialist is required for the slump test. Therefore slump test is used more.
- The method of the slump test is simple and easy. Therefore slump test is used more in fieldwork.
- According to IS code, the nominal aggregate size in fresh concrete in the slump test should not be more than 38 mm.
- The slump test of each batch of concrete mixer can be prepared. During construction slump test is done to get uniform quality of concrete.
- The water-cement ratio can be improved with a slump test.
- The slump test gives good results for the workability of concrete with a 25 to 125 mm slump.
Apparatus of Slump Test
1. Slump Cone
The slump cone is mainly made of stainless steel. The diameter of the slump cone is as follows.
The slump cone has a top diameter of 10 cm and a bottom diameter of 20 cm. The height of the slump cone is kept at 30 cm.
Also Read: Quality Testing of Sand for Concrete | Quality Testing of Sand for Construction | Types of Sand Test
2. Temping Rod
The temping rod is made of stainless steel. The diameter of the temping rod is 16 mm.
3. Baseplate
The base plate is used for a smooth surface and level.
Procedure of Slump Test
- First, take the slump cone and tamping rod to the place where the workability of the concrete is to be checked.
- The inside surface of the slump cone is then cleaned. Oil is applied to the inner surface of the slump cone so that the concrete can slide comfortably into the slump cone.
- The slump cone is then placed on a flat surface. The concrete is then filled layer-wise into the slump cone. Each level is pressed 25 times with a temping rod.
- The top layer is finished with a towel after the concrete is filled up in the slump cone. Now the slump cone is slowly lifted upwards, so the concrete slowly settles down.
- The distance between the surface of the slump cone and the surface of the concrete is called a slump.
Type of Slump
According to the Workability of Concrete, There Are Three Types of a Slump, Which Are as Follows.
1. True Slump
A slump in which the variation is less, i.e., the same in all directions, is called a true slump.
2. Shear Slump
If one-half of the concrete cone slides down, it is called a shear slump. The shear slump is measured as a difference in height between the height of the mold and the average value of subsidence.
If the sample shows a shear slump, the experiment shall be repeated. If in the repeated test also. The specimen shows a shear slump. The slump should be measured and recorded as a shear slump.
Shear slump indicates that the concrete is non-cohesive or harsh and shows the characteristic of segregation. This also indicates poor grading of aggregates.
3. Collapse Slump
If the concrete spreads with the slump cone in elevation, the slump will collapse slump Says. The slump is usually 25 to 75 mm for low workability, 50 to 100 mm for medium workability, and 100 to 150 mm for high workability.
4. Zero Slump
This type of slump has zero difference in the slump test when the concrete mix is very hard. The workability of concrete from the same batch may vary.
Factors Affecting of Slump Test
The Factors Affecting of Slump Test Are as Follows.
- The ground should be level for the slump test. If the ground level is not level, then slump results are not correct.
- The slump test depends on the weather. As a result, it is not accurate in hot weather.
- Depending on the surface of the slump cone, if the surface inside the slump is rough, the result will not be true.
- Transport plays an important role in the slump test.
- Water cement ratio pan plays an important role in the slump test.
Advantage of Slump Test
- The equipment for the slump test is light in weight.
- The method of the slump test is easy.
- The equipment of the slump test can be easily transferred.
- The slump test can be done both in the field and in the laboratory.
- The result of the slump test is obtained fast.
- Equipment for the slump test is cheap.
- Only one man is required for the slump test.
- The slump test gives good results for the workability of concrete with a 25 to 125 mm slump.
- A slump test is done to maintain the consistency of materials like aggregate, sand and admixture, etc.
Disadvantage of Slump Test
- The slump test does not show workability for very wet and dry concrete.
- It does not give workability even in the concrete of hard mixing.
- The workability of the concrete in each batch varies.
- In this type of test, sufficient compaction should be done with the temping rod.
- Different results are obtained on the site and the plant.
- The surface of the base plate for the slump test should be free from vibration.
- Concrete should not be filled together in the slump test. It should be compacted about the level.
- Depending on the surface of the slump cone, if the surface inside the slump is rough, the result will not be true.
- The surface of the base plate for the slump test should be free from vibration.
Also Read: Lab Test on Aggregates at Site
Suggested Ranges of Workability of Concrete.
No | Placing condition | Degree of workability | Slump(mm) |
1 | Pavement using a paver, building concrete, shallow foundation | Very low | 75-80 |
2 | Mass concrete, beam, wall, column, strip footing, canal lining | Low | 25-75 |
3 | Heavily reinforced section in-wall, slab, column, beam | Medium | 50-100 |
4 | Slip formwork, pumped concrete | Medium | 75-100 |
5 | Trench fill, in situ piling | High | 100-150 |
6 | Tremie concrete | Very high | 100-175 |
Like this post? Share it with your friends!
Suggested Read –
- 7 Types of Pavement Markings
- 8 Types of Pointing in Construction
- What Is Theodolite And Their Types
- Credenza Vs Sideboard & Complete Guide
- What Is Shuttering And Their Different Types
What Is a Slump Test?
The slump test is a method used to measure the workability of freshly made concrete. It involves assessing the consistency and flow properties of concrete, which is crucial for determining its suitability for construction purposes.
Why Is the Slump Test Important?
The slump test helps ensure that the concrete mix has the right workability for proper placement and compaction during construction. It allows for adjustments in water-cement ratio and helps maintain uniform quality in concrete batches.
What Equipment Is Used in the Slump Test?
The equipment used in the slump test includes a slump cone, a temping rod, and a base plate. The slump cone is typically made of stainless steel and has specific dimensions for accurate measurements.
What Are the Types of Slump?
The types of slump in concrete are true slump (uniform subsidence in all directions), shear slump (one-half of the concrete cone
slides down), collapse slump (spread with elevation), and zero slump (very hard concrete with no subsidence).
What Factors Affect the Slump Test?
Factors such as ground level, weather conditions, surface roughness inside the slump cone, transportation, and water-cement ratio can affect the results of the slump test. Proper compaction with the temping rod is also essential for accurate measurements.
What Are the Advantages of the Slump Test?
Advantages of the slump test include its simplicity, portability of equipment, quick results, suitability for both field and laboratory testing, and cost-effectiveness. It helps ensure consistent workability and aids in maintaining material consistency.
Leave a Reply